Continuous Emission Monitoring Systems

Product Details:

As per latest CPCB guidelines, it is now mandatory to monitor online continuous Stack Emission Monitoring Systems (CSEMS) in 17 categories of highly polluting industries and in Common Hazardous waste and Biomedical waste incinerators for the parameters(industry/sector specific parameter) mentioned in the consent to operate/authorisation not later than by JUNE 30,2015.

Details:

Product Details:

Applied Techno Systems is Inginiuos manufacturer of Continuous Emission Monitoring Systems which includes Gas ANalyser, Gas Sampling Systems, Tempreture , flow & Opacity dust Monitoring Systems with real time data transmission Systems to CPCB & SPCB.
Applied Continuous Emission Montoring CEMS fullfill the environmental regulatory compliance of various industrieal sources of air pollutant.

Features:

• Microcontroller based embedded intelligent instruments
• Continuous Monitoring of CO2 ,CH4, CO, O2, SO2, NOX (NO NO2), H2, H2S, N2
• Duel wavelength Infra red sensor for Long terms accuracy and stability
• Long Life Electrochemical sensor
• Six Gas Analysis in Single Analyser
• Multi Parameter Single 320 X 240 Graphics LCD Display
• Self diagnostic & Self integrity check
• RS 232/RS 485 and USB Computer Interface
• Excellent low level capability for NOX and SO2 Measurement
• For most of the application sample gas is cooled and dried inside the sampling conditioning systems to avoid the Heated Sample Line.
• Analog 4-20mA output for each gas
• Software solutions for Gas Analysis
• Web Based Real time data transfer

Product Details:

we are indigiuous manufacturer of Online SOX And NOX Analyzer based on elctrecto chemical and NDIR based technology.
Online gas monitoring systems OCEMS has provision for remote calibration facility with Zero & Span gas calibration gas mixture.
OCEMS has special type of sampling probe with dryer systems to avoid the heat tracig line.we use teflon or SS316 sampling tube for interconnection of sampling probe and sampling systems which is integrated with gas analyser.

Product Details:

Online NDIR Based Emission Monitoring Systems as per pollution Control board guidlines with real time data connectivity to CPCB & state pollution control board.

Product Details:

Online Continuous Effluent Monitoring Systems (OCEMS) Model L600 design for testing the water quality ( COD, BOD, TSS,pH & Flow )of Industrial water, Petrochemicals,river or lack etc.


Specifications :

Additional Information:

• Production Capacity: As per requirement
• Delivery Time: 2-3 weeks

Product Details:

Online continuous dust monitoring systems for stack emissions Model ATS 208A are uefull  for industries that need to comply with air quality regulations.
The Stack Guard series operate on the principle of Tribo - Electric charge transfer. The electrical charge carried by dust particles is captured by a highly sensitive Tribo - Electric probe, amplified and then transmited to the control unit. As the current generated by the charge is proportional to the concentration of particles present, an indicatie signal of dust presence results.

Specifications -
Measurement Technique : Tribo-electric charge transfer            Operating Temp (Gas)  : -15 to 250 deg. C  

Additional Information:

• Item Code: HNS90310000
• Production Capacity: 100 Pieces per month
• Delivery Time: Two Week
• Packaging Details: Very Good Packaging

Product Details:

We offer Real Time Online Effluent Monitoring Systems for the measurement of COD BOD TSS PH for the application of ETP & STP with real time data transmission to CPCB and state pollution control board cloud server.The instruments is based on UV absorption technology with autometic cleaning systems.

Product Details:

Online Stack SPM Analyzer Manufacture in Mumbai.Process Trend Monitor and Multi -Purpose Dust Alarm with Display A Real time Continuous indicative dust monitor with logging & alarm capability. Low Cost Solution to Monitoring Requirements.
Application: The stack Guard is used in most situations where the actual or potential presence of particulates creates an indicative monitoring requirement & also where higher cost of a quantative monitor is not justified.
Filter Failure Alarms., Process Control Monitor, Cogeneration Power Plants, Ferrous &Non Ferrous metal Processing Unit, cement Plants & Silos, Petrochemical, Pharma , Boilers & Incinerators Paper Plants etc.

Specification

• Measurement Technique: Tribo - Electric Charger transfer
• Sensitivity: Adjustable over a wide dynamic range
• Operating Temp (Ambient): -15 to 50 deg C
• Operating Temp (Gas): -15 to 250 deg C ("T" Model up to 700 deg C)
• Ranges: 1-1,000mg/m3
• Response Time: Instantaneous
• Installation:Duct Width: 25 mm to 2.2m
• Positioning: 90 deg C to Duct wall
• Communications path Length: up to 1,000 meters
• Socket : Single 1 flat Flanged fitting
• Probe Construction: 316 Grade Stainless Steel
• Sensor Length : 25, 100 or 200 mm ( or Customized)
• Sensor Diameter: 10mm
• Size of Attachement : 115x65x55 mm
• Operating Temp: -15 deg C to 55 deg C
• Display: 128x64 graphic display

Product Details:

Model ATS-208A Gas Analyzer continuously monitors the concentration of gases ranging from 100%V/V down to PPM level. Feature includes a duel wavelength sensor, Remote Sampling, Graphics LCD Display, adjustable level relay output for alarm and 4-20mA output for control purpose and minimal maintenance. Special gas sample Conditioning systems are used to clean and dry the gas sample for accurate and High performance operation. An Internal Pump draw gas sample into the sensor through a dust particle filter from an intake which can be located at distance up to 60 meter form the monitor. The Sensor and Electronic component are housed in tough aluminium housing For hazardous area applications the sensor may be mounted remotely in the hazardous area and safely connected via an zener barrier to the electronics unit in the safe area. Alternatively the electronics unit can be supplied in an Explosion proof enclosure.

Operation-
ATS 208A is an extractivesampling multi-gas analyzer system. The flue gas is extracted using a sample Probe. The gas is than transported via a sample line, to the cooler unit fitted inside the sample managementsystem, where the moisture and particuletesare removed before being directed into themeasurement system. The measurement system is made up of pairs of sensor. Each sensor is Fed alternately with sample gas and air. The sensors generatean electrical output in proportion to a specific gas component. Measured values are then displayed and output as analog signals (4-20mA).

Engineered for the future
Excellent low level emissions capability Wide range of sensor to provide the precision necessary for the level measurement required by legislative limits.  Heated sample line not required in most applications Sample gas is cooled & dried inside the sample measurement system.

Accurate & Reliable SO2 Analysis-
ATS 208A is an accurate and reliable SO2 analyzer. Importantly, it is a low cost alternative to infrared or UV systems, using the latest Advanced Dual Sensor technology. The accuracy & reliability of the Analyzer in the measurement of SO2 beginswith the sample condi?oning ystem. A cooler and acid resistant sample path ensure there is no significant loss during gas transportation. High accuacy sensors inside the analyzer produce a reliable, stable output.

Ideal for Low NOx Measurement
Analyzer designed for very low NOx measurement, importantly, the analyzermeasures both NO and NO2 separately, these are combined to give a true NO2 measurement output. The inherent problems with catalytic NO2 onvertors are therefore completely avoided.

Probes and Sample Lines for all Applications
Our experience will help determine which probe and type of sample line will give the best possible results in your applications. A full range of heated and unheated probes, filters and sample lines is available to meet all requirements, and more importantly, to keep operating continuously and very efficiency, with the minimum of maintenance. Heated filter probes Ceramic probes for hot or acidic conditions Regulated and self-regulating heated sample lines Unheated sample lines.

Product Details:

Continuous Emission Monitoring Systems (CEMS) are devices used to monitor and analyze the concentration of pollutants released into the atmosphere from industrial processes. These systems are commonly used in power plants, refineries, chemical plants, and other facilities that may produce air emissions, to ensure compliance with environmental regulations and to monitor air quality in real-time.

Key Components of CEMS:

1. Sampling System: This part collects a representative sample of the exhaust gases from the stack or emission point.
2. Analyzers: These instruments analyze the chemical composition of the air sample, typically measuring pollutants such as:
3. Sulfur Dioxide (SO₂)
   • Nitrogen Oxides (NOx)
   • Carbon Monoxide (CO)
   • Oxygen (O₂)
   • Particulate Matter
   • Volatile Organic Compounds (VOCs)
4. Data Acquisition and Handling Systems (DAHS): These systems collect, store, and transmit data from the analyzers. They ensure the data is formatted for regulatory reporting.
5. Calibration and Validation Systems: CEMS typically include automatic or manual calibration features to ensure the accuracy of readings. Validation may involve comparison with reference methods or periodic calibration checks.

^{Types of CEMS:}

1. Optical CEMS: These use light-based methods like ultraviolet (UV) or infrared (IR) spectroscopy to detect gases.
2. Electrochemical CEMS: These rely on chemical reactions of gases with electrodes to measure concentrations.
3. Infrared CEMS: These systems use infrared absorption techniques, often used to monitor gases like CO₂ and CO.
4. Chemiluminescence CEMS: These are typically used for NOx monitoring, where the chemical reaction between nitrogen oxides and ozone produces light, which is then measured.

_{Applications:}

Regulatory Compliance: CEMS are often mandated by environmental protection agencies (like the U.S. EPA) to ensure that industrial processes are not exceeding allowable emission limits.

Process Optimization: In addition to regulatory functions, CEMS can also be used for process control to optimize fuel use or reduce waste.

Emission Reduction: Data from CEMS can be used to identify areas where emission control systems need improvement.

Product Details:

Extractive Type Continuous Gas Analyzer Model ATS -208A Gas with dual display

Analyzer continuously monitors the concentration of gasesranging from 100%V/V down to PPM level. Feature includes a duel wavelengthsensor, Remote Sampling, Graphics LCD Display, adjustable level relay output foralarm and 4-20mAoutput for control purpose and minimal maintenance.Special gas sample Conditioning systems are used to clean and dry the gas samplefor accurate and High performance operation. An Internal Pump draw gas sampleinto the sensor through a dust particle filter from an intake which can be located atdistance up to 40 meter form the monitor.The Sensor and Electronic component are housed in tough aluminium housingFor hazardous area applicationsthe sensor may be mounted remotely in thehazardous areaand safely connected via anzener barrier to the electronics unit inthe safe area. Alternatively the electronicsunit can be supplied in an Explosion proofenclosure.

spacification

Additional Information:

• Item Code: ATS-208A
• Delivery Time: 2 WEEKS
• Packaging Details: IN BOX PACKING